110VDC Industrial Battery Chargers with Isolation transformer for Nickel-Cadmium Battery Bank

You are here: Home » News » 110VDC Industrial Battery Chargers with Isolation transformer for Nickel-Cadmium Battery Bank

110VDC Industrial Battery Chargers with Isolation transformer for Nickel-Cadmium Battery Bank

Views: 0 Author: Site Editor Publish Time: 2024-08-02 Origin: Site

To recharge any types of rechargeable batteries, for instance vented or sealed,lead-acid,Ni-Cd, the three-phase rectifiers, empoly a 6-pulse thyristor bridge, fully controlled by PCB board.

Limit the output by dropping Diodes
Isolation transformer and Harmonic filters
Applicable international standard:IEC 60950-1
Panel IP and panel thickness:IP20 Indoor,2mm
Rectifier efficiency:≥90%
AC&DC short circuit current:TBD based on design and below specs.
Mode of controlling output voltage current specify it should be manual /automatic:Both(Manual & Automatic,but the output voltage should be regulated.
Rectifier transformer overload capacity:The Max.rectifier capacity
Type of metering indicators:Both (Analog &Digital)
Installation type:Indoor
Type of Earthing:Solidly
Input:-
3 phase AC Supply 400VAC±20%
50Hz±6%
Power Factor Approx(0.7-1)
Isolation transformer
Output:-
110VDC Regulated with ± 5% (Adjustable)
0-100A
DC Filter
Output Ripple voltage Max 5%rms nominal DC voltage
Charging Mode Selector Switch:
The charging mode should be Automatic and Manual with independently adjustable of charging via selector switch as:
Float (Trickle) Charge
Hi-Rate (Boost) Charge
Current Limit Setting
Float and boost Charge Rating capacity:Adjustable for the batteries with capacity of (100AH-600AH)
Slow-Start:
The Slow Start function is used to prevent high current surge during powering up of the rectifier and the Circuit only operate during the start-up of the rectifier.
Typically,the design is chosen to give the slow-start ramp of I0seconds from start up.
Operation Environment
Audible Noise 55 dBA@1.5m±10%
Temperature Range -25°C to+55°C continuous
Humidity 0 to 95% @ 25°C
Altitude≥2000m above sea level.
Cooling System
Low noise Fan with Air Filter
Protection:
AC DC Surge
AC Input Over and Under Voltage Protection
AC DC Surge Suppressers
AC Input Over and Under Voltage Protection
DC output Over Voltage Protection
DC output over Current Protection
DC Output Earth Fault Protection
Metering:
AC Input Voltage Indicator
AC Input Current Indicator
DC Output Voltage Indicator(Load)
DC Output Current Indicator (Load)
DC Output Voltage Indicator(Batteries)
DC Output Current Indicator (Batteries)
Battery Status LED (Rate of Charge)
Multi Alarm system and LED Indications
Rectifier Normal Operation
Alarm sounder and Silence button
AC Input Reverse Phase Sequence LED
AC Input phase failure and Low Voltage Alarm and LED
Low Voltage Output Alarm and LED(Adjustable)
Input and Output MCB or Fuses trip Alarm
High Temp.Inside the Charger or semiconductor
Colling Fan has Failed
Ground Fault"-VE"
Ground Fault"+VE"
Charger Fail
Terminal and cabling connections
Bottom connected
Separate Terminal Block for the Input,Load and Batteries
Applications
DABS Substations.
DABS Junction Stations.

110VDC Industrial Battery Chargers with Isolation transformer

Nickel-Cadmium Battery Bank 110vdc Battery Bank Switchmode DC Switch Battery Charger 110Vdc Output Battery Charger 110VDC Industrial Battery Chargers 110VDC 20A Battery Charger 110VDC Charger 110VDC Battery CHARGER 110V DC UPS system Industrial DC UPS Battery Chargers

ABOUT NASN

GUANGZHOU NASN POWER CO.,LTD is a professional EV charger, DC power supply and battery storage solution provider and enterprise in China, a wholly owned subsidy of NASN ELECTRONICS (HONGKONG) CO., LIMITED.

ISO9001

QUICK LINKS

PRODUCT CATEGORY

CONTACT US

   Contact person : Florence
   Tell : +86-20-86857678
   Phone : +86-135 1058 5626
    QQ : 28243245
    E-mail : info@nasn.cn